I just recently switched from Studio to Storyline and I am going crazy trying to figure out how from the results slide how to get the user to jump to one slide if they fail or another slide if they pass. How is this done in Storyline?
Thanks you for the reply, but that did not help. I tried adding triggers directly to Fail and Pass slides that when Next was clicked to jump to the appropriate slide. The triggers disappeared. As you can see below, I then tried to create triggers for the Results slide and that is not working either.
Lisa "Dawn" Chamberlin | Instructional Designer, Corporate Training |Time Zone: EST
Ocwen Financial Corporation
P: (972) 782-9283
IP ext.: 72367
Lisa.Chamberlin@ocwen.com | www.Ocwen.com
********************************************************************************************
This E-mail message and any attachments are intended solely for the use of the addressee hereof and may contain information that is confidential, privileged and/or exempt from disclosure under applicable law. Delivery of this message to any person other than the intended recipient shall not constitute a waiver of any right, privilege or exemption. If you are not the intended recipient, please immediately notify the sender by reply E-mail and permanently delete this message from your system without reproducing or disclosing it to any third party. While Ocwen Financial Corporation and its subsidiaries take reasonable precautions to prevent transmission of software viruses, we cannot guarantee the same and we therefore disclaim liability for any damage sustained by you or any third party as a result thereof
********************************************************************************************
just a note when you reply via email it displays your entire email signature in the post so you can come in and edit to remove if you wish. Also, anything you attach via email doesn't display in the post, so the image you attached isn't visible here.
Can you perhaps share the .story file and someone can take a look to try and help you.
I attached the story file to this response. Please let me know if that is not the correct way to submit it. It is a small file with 5 dummy questions and an End of Assessment slide and Congratulations slide. When the user fails, they should be directed to the End of Assessment slide; if passes go to the Congratulations slide.
Thanks for looking at the file.
Dawn
********************************************************************************************
This E-mail message and any attachments are intended solely for the use of the addressee hereof and may contain information that is confidential, privileged and/or exempt from disclosure under applicable law. Delivery of this message to any person other than the intended recipient shall not constitute a waiver of any right, privilege or exemption. If you are not the intended recipient, please immediately notify the sender by reply E-mail and permanently delete this message from your system without reproducing or disclosing it to any third party. While Ocwen Financial Corporation and its subsidiaries take reasonable precautions to prevent transmission of software viruses, we cannot guarantee the same and we therefore disclaim liability for any damage sustained by you or any third party as a result thereof
********************************************************************************************
attachments don't come through when you attach via email - Instead of clicking Reply click View and you'll come into the forum and be able to attach using the grey 'add attachment' button at the bottom of the post.
9 Replies
Hi Dawn and welcome to Storyline!
When you insert a Result slide there will be a success and fail layer automatically created.
Depending on the score, one of those layers will display. You can then navigate from the layer to another slide if you wish to.
Here is a tutorial that might explain it better but feel free to share you .story file if you are still having issues.
Thanks you for the reply, but that did not help. I tried adding triggers directly to Fail and Pass slides that when Next was clicked to jump to the appropriate slide. The triggers disappeared. As you can see below, I then tried to create triggers for the Results slide and that is not working either.
[cid:image001.png@01D29762.3A5EDB90]
Thanks.
Dawn
Lisa "Dawn" Chamberlin | Instructional Designer, Corporate Training |Time Zone: EST
Ocwen Financial Corporation
P: (972) 782-9283
IP ext.: 72367
Lisa.Chamberlin@ocwen.com | www.Ocwen.com
********************************************************************************************
This E-mail message and any attachments are intended solely for the use of the addressee hereof and may contain information that is confidential, privileged and/or exempt from disclosure under applicable law. Delivery of this message to any person other than the intended recipient shall not constitute a waiver of any right, privilege or exemption. If you are not the intended recipient, please immediately notify the sender by reply E-mail and permanently delete this message from your system without reproducing or disclosing it to any third party. While Ocwen Financial Corporation and its subsidiaries take reasonable precautions to prevent transmission of software viruses, we cannot guarantee the same and we therefore disclaim liability for any damage sustained by you or any third party as a result thereof
********************************************************************************************
Hi Dawn
just a note when you reply via email it displays your entire email signature in the post so you can come in and edit to remove if you wish. Also, anything you attach via email doesn't display in the post, so the image you attached isn't visible here.
Can you perhaps share the .story file and someone can take a look to try and help you.
Are you using SL2 or SL360?
I attached the story file to this response. Please let me know if that is not the correct way to submit it. It is a small file with 5 dummy questions and an End of Assessment slide and Congratulations slide. When the user fails, they should be directed to the End of Assessment slide; if passes go to the Congratulations slide.
Thanks for looking at the file.
Dawn
********************************************************************************************
This E-mail message and any attachments are intended solely for the use of the addressee hereof and may contain information that is confidential, privileged and/or exempt from disclosure under applicable law. Delivery of this message to any person other than the intended recipient shall not constitute a waiver of any right, privilege or exemption. If you are not the intended recipient, please immediately notify the sender by reply E-mail and permanently delete this message from your system without reproducing or disclosing it to any third party. While Ocwen Financial Corporation and its subsidiaries take reasonable precautions to prevent transmission of software viruses, we cannot guarantee the same and we therefore disclaim liability for any damage sustained by you or any third party as a result thereof
********************************************************************************************
Hi Dawn
attachments don't come through when you attach via email - Instead of clicking Reply click View and you'll come into the forum and be able to attach using the grey 'add attachment' button at the bottom of the post.
Sorry about that. It's been several years since I have posted a question.
Hi Dawn
see the triggers on the result slide - I have added conditions to each jump to next button trigger depending on the result.
Hope that works for you and shout out if you need more help
Wendy, you are the best. It is working now and I see I was using the wrong parameters in my triggers. Many thanks for your quick help.
Glad to help Dawn and all the best for your project.
This discussion is closed. You can start a new discussion or contact Articulate Support.