Forum Discussion
Articulate 360 Peek Window issues
I apologize is this is covered elsewhere, but I didn't see it if it is. I have dual monitors because I find it easier to develop that way (pull up material in Word on one screen, copy into Storyline on the other). The Peek screen recorder seems to be a bit confused by that. When I try to record something, the "window" that shows up is about four inches from the screen I choose.
For example, if I choose "full screen" of the monitor on my left, it puts the red box mostly in the middle of the two monitors instead of fully over the left side. I am posting a screen shot of where the window goes on this page for an example (attached). The weird thing is that it will record the screen as if it is in the proper place (though does record the line of record box itself). If I move it with the move crosshairs to cover the window fully over the where I want it, it does not record correctly (it acts offcenter). I've tried playing with various things in Properties to see if it is a "compatability" thing, but haven't found an answer yet. Anyone have any ideas?
Sorry you're having trouble with Peek, Anton. Can you tell me a bit more about your set up?
Specifically...
- What version of Windows are you using?
- Are you using dual monitors?
- What happens when you try recording with Peek?
Greetings
I am running Windows 10, I have dual monitors.
Peek does not capture the section of screen that is in the RED box
I set the RED box to record the whole of screen 1, but what it recorded was ¼ of screen 2 (LHS of video)https://360.articulate.com/review/content/f64b69b5-fd08-4197-8eb0-ae125c8c9e40/review
I have had to stop using Peek because of this. So far nothing I have tried seems to capture the exact area I need. I hope because of this thread it will get fixed:)
Hi Anton and Karyn,
I'm sorry you're still struggling with this. Have you tried disabling the additional monitor to see if that is interfering with the record set up? Also when choosing the recording section are you picking a particular window or choose to record full screen?
I am having the exact same issue as the other users describe. Windows 10. Box is off center to the right by 3-4 inches. Have tried both recording full screen and particular window. Same issue in Storyline 360 and Replay 360. It records correctly, but playback shows the red border from the recording window. Works fine when recording with only one monitor connected, but being able to use this product with dual monitors is a must. Any resolution yet?
Thanks for checking in, Ruth. We don't have a resolution for the Peek issue yet. However, it's strange that you're also having this problem in Storyline and Replay 360.
I've opened a case on your behalf so our Support Engineers can take a closer look at this. Keep an eye out for an email from our team!
Also having this issue. We were going to purchase a 360 Teams plan but this is hindering our decision to move forward as we have not been able to successfully use Peek to record software simulations.
Hi Krystin,
I'm sorry you've run into such trouble recording with Peek. It seems to be something specific to users who have a dual monitor set up and are trying to record. Does that match what you're seeing?
Are you able to record if you disconnect from your additional monitor?
No, I can't use it at all
Thanks,
Krystin Blakemore - Hardware Technical Specialist
AssetWorks LLC. www.assetworks.com
Fuel & KeyValet Support: 800-900-8152 Press 1 for Customer Care then Press 3 for Fuel Focus and KeyValet SupportNEW: Access Support Documents through the AssetWorks Community
You can now find the latest documentation such as CANcodes, troubleshooting articles, and more.
See these instructions on how to access these valuable resources.Greetings
I ran a test with one monitor (screen) only, you are correct it works fine. The problem exists when two monitors are activeKind Regards
Anton Noffke
Hi Krystin,
Thanks for testing that first! If you're not able to use Peek at all, I'd like you to work with our Support team so that they can dig in a bit deeper with you. I'll open a case for you so please keep an eye out for an email from Support@articulate.com.
Also just a note: Replying via email will include your signature. You can edit out your contact information from your post if you'd like!
Thanks, Anton! Glad to hear that worked.
I also am having an issue using Peek 360 on a windows machine. I have disconnected my second monitor and restarted. The Peek window still does not open. The icon shows up in the bar, but as soon as I mouse over it disappears. /sadface Looking forward to a fix, need to do some screen captures for current project.
Hi April,
Sad face, indeed! 😕 Peek is my favorite tool because of how easy it is, so let's get you up and running!
Did you try any of the other steps here such as repairing Peek, and attempting to rerecord while only on one monitor after that? That would be what I'd try next, and if you're still stuck - can you also connect with our Support Engineers? They can take a deeper dive into your system setup and figure out what else may be contributing to this.
Repair does not work because the icon disappears as soon as I mouse over. Our machines are still on Windows 7 (could be part of the issue, company owned I have no control). You are welcome to have a Support Engineer contact me, Thank you.
