Continued issues with text running off slide

From reading all of the above comments I can see that my issue isn't unique.  Reading Craig's comments above, I checked my powerpoint size and it was 16:9. However I didn't change the slide master size before importing into Storyline.  However I have saved it several times over last few days and today when I go back it, then text is still running off the slides again even after I have corrected and saved it.  This is extremely frustrating!

Hello Alison,

Thank you for reaching out and sharing that you're experiencing a similar issue to what Craig shared above. It looks like he was able to track down the culprit.

We do have an open issue with our team specific to this scenario:

1. Import PowerPoint presentation to Storyline 360.
2. Apply any built-in theme using the Design tab.
3. Save and close the project file.
4. Reopen the project file.
5. Text box no longer displaying as expected.

Does this match your experience as well?

I'd like you to share your project file with our support engineers to investigate what's happening with your permission. You can share it privately by uploading it here. It will be deleted when troubleshooting is complete.

Allison:  I seem to recall that the 16:9 widescreen setting in PowerPoint was part of the problem. 

Sorry, if I wasn't clear.  The 16:9 widescreen setting in PowerPoint is too wide for Storyline so these wide text boxes would carry over creating a less than desired result.  So once, resetting to the old 4:3 setting there is usually a little resizing to be done in PowerPoint before importing.  Then, import.  Obviously, I wouldn't spend too much time on that before running a test import.   You will definitely want to have a backup of your original widescreen PowerPoint just in case.  

Crossing my fingers for you.   Good luck.  

What was the outcome for this? Mine is doing this and I am not importing from PPT. I am using 16:9. 

Hi, I'm having this issue and I did NOT import from PowerPoint. Every time I close the file, and then re-open it, my text boxes run off the screen (usually they change themselves to 200-380% wider). The height is unaffected.

Also, my custom line spacing disappears. Anyone else?

Thanks for the welcome. This is my first post with this email - you'll find me on here going back at least 8 or 9 years. You guys are the best. 

So now the text wrapping seems to be ok, but oddly enough some of my triggers have disappeared and all of my animations. I've exported everything to word, and thank to the new media library also exported all of my graphics, and will start again totally from scratch. I'll also try it this time with a 4:3 aspect ratio instead of a 16:9

After years of this issue being reported by multiple users, this doesn't seem to be resolved. It occurred on Friday 7/8/2022 when importing from PowerPoint. After correcting 50 slides, I reviewed the work and sent the link out to my team. This morning 7/11/2022 when I went back in to add some knowledge check slides the title on the slide was reformated, and about half the slides with test boxes ran off the slide. It's just frustrating to be paying so much for a program that is supposed to be helpful only to be sabotaged.  

Please fix the issues. 

Hi, I'm not sure if this is the correct thread or if there is another appropriate one.

I'm having an issue with text overrun and this is on a slide created and Not from PPT import.
It is also running off the edge of the text box, not the slide body.

It is beyond frustrating for what should be one of the most simple slide types.
Changed from short 256 characters / to Essay 5000  and 2500 in addition to test if character limit impact
(I have an Essay slide earlier in Q templates (set at 2500 characters)  and all works fine on that one-)

Editor - The text box on the slide is set to a position via the editor to sit just in from both sides and sit below the Question body text etc with the text box displaying "Type your text here"
In line with the edge of the box/slide outer in the editor.

Preview the text box appears smaller in Width and Height and the text runs off the edge/overruns the text box but not the slide.
( see image) 

Seemingly the text is within the parameters of the text box but the "text box" is not displaying in line with that set position.

- Format Shape / Text Box is set to Fixed Size  + Add Scroll bar, but no about of options or changes seems to fix.

- AS360 is the latest version / up to date with text autofit improvements etc.  

Any assistance would be appreciated as this is now the only aspect holding up a project. 

Hi Jason,

I'm sorry you're having issues with your textboxes! I would love the opportunity to troubleshoot this for you! Would you be willing to share your file here or with our support engineers privately in a support case?

Thanks for reaching out!

Hi Jason,

Great idea opening a case! I confirmed that it is now in our system, and one of our Customer Support Engineers will reach out to you shortly. To avoid confusion and keep all the information in one place, let's continue the conversation in your support case.

Thanks for your patience!